> 產品介紹 > Switching Adapter > Desk Top 桌上型電源

產品介紹

24W Desk Top

This specification describes the physical, functional and electrical characteristics of the 36 watts, single output 24 V1.5 A switching power supply

AC / DC Single Output Desk-Top Type Low power consumption Efficiency: Meet DOE Level VI, UL62368, CB 62368

快速詢價相關文件

1.SCOPE：

1-1.This specification describes the physical, functional and electrical characteristicsofthe 36 watts,

single output24V 1.5A Description Wall Mount Open Frame

2.INPUTCHARACTERISTICS:

2-1.Input Voltage &Frequency

switching power supply. Desk-Top Others

Item	Min.	Normal.	Max.	unit
Input voltage range	90	100-240	264	Vac
Input frequency range	47	50/60	63	Hz

2-2.Input current
Input current should be lowerthan 2-3.InrushCurrent
At Full Load ,25℃, Cold Start；

1.2Arms full-loadat

100-240 Vac input voltage conditions.

No Component Over Stress and No Fuse Blow No Damage To The Power Supply。
2-4.Stand-by Consumption & Average Efficiency In Active.Comply with following regulation:

	Regulations	Efficiency Level	For
V	U.S.DOE 10 CFR Part 430	Level VI		V	Basic Voltage model
V	EU Code of Conduct Version 5,Tier 2	Level VI			Low Voltage model
	(EU)2019/1782	Level VI

Stand-byconsumption 0.1 WMax.
Average Efficiency in active87.403%% Min.
※All test condition is based on input voltage 115/230Vac 60/50Hz at ambient 25℃ after 30 minutes in full load.

3.OUTPUTCHARACTERISTICS:

3-1.Output Characteristics

Item	Min.		Rated		Max.			Test conditions
Output Voltage	22.80	Vdc	24.00	Vdc	25.20		Vdc	NO Load
Output Voltage	22.80	Vdc	24.00	Vdc	25.20		Vdc	FULL Load
Output Load	0	A	/		1.5		A
Turn on Delay Time	/				3		S	Full Load & 90Vac/63Hz and 264Vac /47Hz @ Ta=25°C
Hold Up Time	10	m S	/					Full Load & 115Vac/60Hz and 230V/50Hz,@Ta=25°C
Capacitance load	/		1000UF		/			100 ~240Vac, Full load
Ripple & Noise	Max.		240			mVp-p		Full Load & 115Vac/60Hz and 230V/50Hz,@Ta=25°C (Note 1)
Note 1: Ripple voltage measurement is tested with an oscilloscope set at a 20M Hz bandwidth & output wire 100 mm terminated with 0.1uF ceramic capacitor & parallel with 10uf low ESR electrolytic aluminum capacitor at full load.

Output voltage, load current, voltage regulation and output noise of power supply should meet the specifications, which defined on the tables below:

4.Output Protection:

5. EnvironmentSection

Item	Min.		Max.		Remarks
Operating Temperature :	0	°C	40	°C	Unit shall comply electrical &machenical requirements when it recovers to normal ambient temperature after removed from strorageconditions.
Operating Humidity：	10	%RH	90	%RH
Storage Temperature :	-10	°C	60	°C
Storage Humidity :	5	%RH	95	%RH

6. Dielectric WithstandVoltage(Hi-pot)

The Adapter shall beapplied 3000 Vac for 60 seconds or4242Vdc for 60 seconds between

ACinputterminalsandoutputterminals.Thecutoffcurrentisspecified≦ 10mA.
(Note: In mass production, the Hi-pot voltage as above can be increased 20%, and the test time can be reduced to 3 seconds to test)

7. Insulation Resistance:
Primary to secondary ≧ 10 M ohm. 500 VDC.

8. EMI Requirement

The adapter complies with :

V FCC Part 15 Class B V EN55032 Class B J55032 Class B

AS/NES 3548 Class B CNS13438 Class B V ICES-003 Class B

GB/T9254 Class B V EN55035 Class B

9 ESD: ± 8KV air discharge, ± 4KV contact discharge